Free Phone: 0800 485 990 (NZ)

Power Probe 4 Master Combo Kit PPKIT04

Power Probe 4 Master Combo Kit PPKIT04

Combines the Power Probe 4, PPECT3000 and various accessories to provide the ultimate combination of diagnostic and circuit-testing capabilities.

The Power Probe 4 provides simplified testing of Motors, Lights, Relays, and Sensors, and even Fuel Injectors. Also, like all Power Probe circuit-testers, it supplies Power and Ground for functional component testing on or off the vehicle. The PPECT3000 will help you trace short and open circuits quickly and accurately.

Buy Online ...

The PPKIT04 Kit includes:

  • Power Probe 4
  • ECT3000 Transmitter
  • ECT3000 Receiver
  • Power Probe Tip
  • 3 Light Bulb Adapters
  • Universal Adapter
  • Alligator Clip Adapter
  • Blade Probe Adapter
  • Back Probe Adapter
  • Small Piercing Probe
  • Large Piering Probe
  • Battery Clipset
  • Battery Clipset for the PP4
  • 3ft Lead
  • Self-resetting Circuit Breaker
  • AAA Batteries

Features

  • Supply Power or Ground for Functional Component Testing
  • Self-Resetting Thermal 8 Amp Circuit Breaker
  • Multiple DC Volt readings on the same display
  • Ohmmeter provide active feedback
  • 12 – 24 Volt Range
  • Bad Ground Indicator
  • Continuity Tester
  • Component Tester
  • AC-RMS, AC Peak to Peak, Frequency and Pulse Width indicators are available for signal testing
  • Fuel Injector tester for easy circuit diagnosis
  • PCM/ECM Driver supplies safe voltage for testing computer driver circuits
  • PPECT Mode for signal detection of open circuits
  • Active LED Lighting for illuminating workspace
  • Power Cable Length of 23 Feet
Product Specifications  
Min Operating Voltage 8 VDC
Max Operating Voltage 30 VDC
Max Tip Voltage 450 Volts
Probe Tip Resistance to Ground 350 K Ohms
Computer Safe 0.1mA floating tip
Voltage Measuremen -100 to 200 VDC / VAC
Voltage Resolution -99.99 to 99.9 V - 0.01 V (10mV) 100.0 to 199.9 V - 0.1V ( 100mV )
Glitch Capture >380uS Min Pulse Width
Power Feed Test <30mA
Resistance Measurement 0.1 Ohms to 10K Ohms
Frequency Measurement 1Hz to 9999Hz
Driver Test 50 Ohm Pull up on Tip Green LED and Tone when < 1 Volt
ECT Signal Detection 2 Sec.
Fuel Iniector Mode LED Flash @ Min 35V @ 100uS Pulse
Red LED Response Within 0.5V BATT V in Voltmeter Mode and < 10 Ohms in Power Feed Test Mode
Green LED Response < 10 Ohms in both Power Feed Test Mode and Voltmeter Mode
Circuit Breaker 8 Amp Thermal- Auto Reset

 

Typical Response    
8 amps 10amps 15amps 25amps Short Circuit
No Trip 20min 6 sec. 2 sec. 0.3 sec.

circuit breaker photo maestro

  • Trace Out a Short Circuit to Chassis Ground
  • Tracing Out a Battery Drain or Current Draw
  • Isolate your Circuit
  • Verify the Short Circuit to Ground
  • Verify an Open Circuit
  • Short Circuit inside a wire harness
  • Reception Distance from 1 inch to 8 inches
  • Tracing Circuits that are shielded (Plastic Panels, Pillars, and Carpet)
  • Shut off time is now 10 mins

Transmitter Spec

  • Min Operating Voltage 8 VDC
  • Max Operating Voltage 48 VDC
  • Working Current: 200mA
  • Working Frequency: 4KHz
  • Max Operating Relative humidity: 80% ( Non-condensation)
  • Max Storage Relative humidity: 80 % (Non-condensation)

Receiver Spec

  • Power Supply: 2 x 1.5V AAA
  • Working Current: When not signal be detected <15mA
  • Power Consumption when power off:<10uA
  • Max Operating Temp: 50°C
  • Max Storage Temp: 70° C
  • Max Operating Relative humidity: 80% (Non-condensation)
  • Max Storage Relative humidity: 80% (Non-condensation)

You can purchase an optional 20 Foot extension cable

pdf iconPower Probe IV Manual

pdf iconPower Probe ECT3000 Manual