Combines the Power Probe 4, PPECT3000 and various accessories to provide the ultimate combination of diagnostic and circuit-testing capabilities.
The Power Probe 4 provides simplified testing of Motors, Lights, Relays, and Sensors, and even Fuel Injectors. Also, like all Power Probe circuit-testers, it supplies Power and Ground for functional component testing on or off the vehicle. The PPECT3000 will help you trace short and open circuits quickly and accurately.
The PPKIT04 Kit includes:
- Power Probe 4
- ECT3000 Transmitter
- ECT3000 Receiver
- Power Probe Tip
- 3 Light Bulb Adapters
- Universal Adapter
- Alligator Clip Adapter
- Blade Probe Adapter
- Back Probe Adapter
- Small Piercing Probe
- Large Piering Probe
- Battery Clipset
- Battery Clipset for the PP4
- 3ft Lead
- Self-resetting Circuit Breaker
- AAA Batteries
Features
- Supply Power or Ground for Functional Component Testing
- Self-Resetting Thermal 8 Amp Circuit Breaker
- Multiple DC Volt readings on the same display
- Ohmmeter provide active feedback
- 12 – 24 Volt Range
- Bad Ground Indicator
- Continuity Tester
- Component Tester
- AC-RMS, AC Peak to Peak, Frequency and Pulse Width indicators are available for signal testing
- Fuel Injector tester for easy circuit diagnosis
- PCM/ECM Driver supplies safe voltage for testing computer driver circuits
- PPECT Mode for signal detection of open circuits
- Active LED Lighting for illuminating workspace
- Power Cable Length of 23 Feet
| Product Specifications | |
| Min Operating Voltage | 8 VDC |
| Max Operating Voltage | 30 VDC |
| Max Tip Voltage | 450 Volts |
| Probe Tip Resistance to Ground | 350 K Ohms |
| Computer Safe | 0.1mA floating tip |
| Voltage Measuremen | -100 to 200 VDC / VAC |
| Voltage Resolution | -99.99 to 99.9 V - 0.01 V (10mV) 100.0 to 199.9 V - 0.1V ( 100mV ) |
| Glitch Capture | >380uS Min Pulse Width |
| Power Feed Test | <30mA |
| Resistance Measurement | 0.1 Ohms to 10K Ohms |
| Frequency Measurement | 1Hz to 9999Hz |
| Driver Test | 50 Ohm Pull up on Tip Green LED and Tone when < 1 Volt |
| ECT Signal Detection | 2 Sec. |
| Fuel Iniector Mode | LED Flash @ Min 35V @ 100uS Pulse |
| Red LED Response | Within 0.5V BATT V in Voltmeter Mode and < 10 Ohms in Power Feed Test Mode |
| Green LED Response | < 10 Ohms in both Power Feed Test Mode and Voltmeter Mode |
| Circuit Breaker | 8 Amp Thermal- Auto Reset |
| Typical Response | ||||
| 8 amps | 10amps | 15amps | 25amps | Short Circuit |
| No Trip | 20min | 6 sec. | 2 sec. | 0.3 sec. |
- Trace Out a Short Circuit to Chassis Ground
- Tracing Out a Battery Drain or Current Draw
- Isolate your Circuit
- Verify the Short Circuit to Ground
- Verify an Open Circuit
- Short Circuit inside a wire harness
- Reception Distance from 1 inch to 8 inches
- Tracing Circuits that are shielded (Plastic Panels, Pillars, and Carpet)
- Shut off time is now 10 mins
Transmitter Spec
- Min Operating Voltage 8 VDC
- Max Operating Voltage 48 VDC
- Working Current: 200mA
- Working Frequency: 4KHz
- Max Operating Relative humidity: 80% ( Non-condensation)
- Max Storage Relative humidity: 80 % (Non-condensation)
Receiver Spec
- Power Supply: 2 x 1.5V AAA
- Working Current: When not signal be detected <15mA
- Power Consumption when power off:<10uA
- Max Operating Temp: 50°C
- Max Storage Temp: 70° C
- Max Operating Relative humidity: 80% (Non-condensation)
- Max Storage Relative humidity: 80% (Non-condensation)
You can purchase an optional 20 Foot extension cable
